RoHS exemptions are one of the most misunderstood parts of EU electronics compliance. A restricted substance such as lead or cadmium is still permitted in a specific application when that use is listed as an exemption, but the rules differ by product category, each exemption carries an expiry date, and separate provisions govern spare parts and products already on the market.
This guide explains how RoHS exemptions work for medical devices, monitoring and control instruments, industrial and test equipment, and legacy products. It covers the two exemption lists, the validity periods that apply to each category, the renewal process, and the "repair as produced" rules that keep older equipment serviceable.
The underlying restriction sits in Directive 2011/65/EU, known as RoHS 2. For a plain-language overview of the restriction itself, see Certivo's RoHS framework page.
Working out which exemptions your products rely on, and when each one expires? A compliance review maps restricted-substance exemptions against your bill of materials.
What a RoHS exemption actually is
RoHS 2 restricts ten substances in electrical and electronic equipment (EEE): lead, mercury, cadmium, hexavalent chromium, PBB and PBDE, plus four phthalates (DEHP, BBP, DBP and DIBP). The limit is 0.1% by weight in any homogeneous material, except cadmium at 0.01%.
An exemption does not exempt a product or a company. It permits a specific use of a restricted substance in a defined application, because a technically and economically viable substitute is not yet available. The European Commission makes this explicit in its RoHS guidance: an exemption covers a use, and the burden sits with the manufacturer to show that a given application falls within the wording of a listed entry.
That distinction matters for the bill of materials. A single product can rely on several exemptions at once, each with its own scope, concentration conditions and expiry date. When an entry is narrowed or expires, only the parts that depend on it are affected, which is why exemption tracking happens at component level rather than product level.
Annex III and Annex IV: two exemption lists
RoHS 2 holds exemptions in two separate annexes, and the split follows product category.
Exemption list | Applies to | Purpose |
|---|---|---|
Annex III | All eleven EEE categories | General exemptions available across the market |
Annex IV | Categories 8 and 9 only | Exemptions specific to medical devices and monitoring and control instruments |
Category 8 is medical devices. Category 9 is monitoring and control instruments, including industrial monitoring and control instruments. These two categories carry their own dedicated list (Annex IV) on top of the general list (Annex III), because they rely on long-lived, safety-critical applications where substitution takes longer to validate.
A medical device manufacturer therefore checks both annexes: the Annex III entries that apply to its category, and the Annex IV entries written specifically for medical and instrument applications.
RoHS Annex III and Annex IV exemption lists compared for medical and monitoring equipment
Click on image to view full
How long RoHS exemptions last by category
Every RoHS exemption has an end date. Under Article 5(2) of the Directive, the maximum validity period depends on the category.
Category (Annex I) | Maximum validity of a new or renewed exemption |
|---|---|
1 to 7, 10 and 11 | Up to 5 years |
8 (medical devices) and 9 (monitoring and control, including industrial) | Up to 7 years |
For the Annex IV entries that existed on 21 July 2011, the maximum validity is seven years from the relevant scope dates in Article 4(3), unless a shorter period is specified. The longer window for Categories 8 and 9 reflects the time needed to qualify alternative materials in regulated and industrial equipment.
A validity period is a maximum, not a guarantee. The Commission can grant a shorter term, and renewal is decided case by case. Certivo's analysis of the 2025 restructuring in what the latest lead exemption changes really mean shows how a single broad entry can be split into narrower sub-entries with different expiry dates.
RoHS exemptions for medical devices (Category 8)
The substance restrictions applied to medical devices placed on the EU market from 22 July 2014, to in vitro diagnostic (IVD) medical devices from 22 July 2016, and the four phthalates from 22 July 2021 for medical devices.
Medical device manufacturers rely on Annex IV entries for applications such as lead in solders and detectors, mercury in certain sensors, and cadmium and mercury in detectors for ionising radiation. Each entry has conditions and an expiry date, and the seven-year maximum validity gives longer lead time than consumer electronics receive.
Active implantable medical devices sit outside the scope of RoHS 2 under Article 2(4). For a view of the broader device compliance picture, see Certivo's medical devices and equipment industry page.
Monitoring, control and industrial instruments (Category 9)
Category 9 covers monitoring and control instruments, and separately, industrial monitoring and control instruments. The scope dates differ:
Monitoring and control instruments: substance restriction from 22 July 2014.
Industrial monitoring and control instruments: substance restriction from 22 July 2017.
Four phthalates: from 22 July 2021 for monitoring and control instruments.
Typical Annex IV entries for Category 9 include mercury in melt-pressure transducers, cadmium anodes in oxygen sensors, and mercury in reference electrodes and relays within defined limits. Because these instruments are often embedded in larger systems and have long service lives, the seven-year validity and the spare-parts provisions below are central to keeping installed equipment serviceable.
Is test and measurement equipment in scope of RoHS?
Test and measurement equipment is a frequent source of confusion. The answer turns on how the equipment is classified and supplied.
Commercial test and measurement instruments sold on the EU market generally fall within Category 9 (monitoring and control instruments) and are in scope, subject to Annex III and Annex IV exemptions.
Equipment designed solely for research and development, made available only on a business-to-business basis, is excluded from scope under Article 2(4)(j).
Test equipment that is specifically designed and installed as part of a large-scale stationary industrial tool (LSSIT) or large-scale fixed installation (LSFI) can fall outside scope under Article 2(4)(d) and (e). Standalone test equipment that is not integrated into such an installation remains in scope.
The LSSIT and LSFI exclusions are interpreted narrowly, and the European Commission's RoHS FAQ places the burden on the manufacturer to justify why a given tool or installation qualifies as "large scale." For manufacturers of industrial machinery, the scope question should be resolved before exemption tracking begins. See Certivo's industrial machinery and heavy equipment page for the wider compliance context.
Legacy products, spare parts and "repair as produced"
A core principle of RoHS 2 is "repair as produced." Equipment lawfully placed on the market does not become non-compliant when a later exemption expires, and it can be repaired with parts built to the rules that applied when it was first sold.
Two articles govern this.
Article 4(4) states that the substance restriction does not apply to cables or spare parts for the repair, reuse, updating of functionalities or upgrading of capacity of EEE placed on the market before the relevant cut-off date:
EEE placed on the market before | Category |
|---|---|
1 July 2006 | Original RoHS 1 scope (categories 1 to 7, 10) |
22 July 2014 | Medical devices |
22 July 2016 | In vitro diagnostic medical devices |
22 July 2014 | Monitoring and control instruments |
22 July 2017 | Industrial monitoring and control instruments |
22 July 2019 | Other EEE brought in under category 11 |
Article 4(4)(f) adds the key legacy rule: the restriction does not apply to spare parts for EEE that benefited from an exemption and was placed on the market before that exemption expired, as far as that specific exemption is concerned. In practice, an installed instrument that relied on a now-expired exemption can still be repaired with parts relying on that same exemption.
Article 4(5) allows reused spare parts recovered from older EEE to be used again, provided the reuse takes place in auditable closed-loop business-to-business return systems and is notified to the customer.
The planning challenge is tracking the placed-on-market date of installed equipment against the exemption its service parts depend on. Certivo's guidance on future-proofing supply chains against RoHS risk addresses how to keep that history auditable.
RoHS legacy and spare parts cut-off dates by equipment category under Article 4(4)
Click on image to view full
The renewal process and the move to ECHA
Exemptions do not renew automatically, but a timely application protects continuity.
A renewal application must be submitted no later than 18 months before the exemption expires (Article 5(5)).
If a valid renewal application is filed in time and the Commission has not yet decided, the exemption remains valid until a decision is made. Installed and new equipment relying on it stay compliant during the review.
From 13 August 2027, Directive (EU) 2025/2456 moves the handling of exemption applications and the supporting scientific and technical work to the European Chemicals Agency (ECHA), as part of the "one substance, one assessment" reform. A new completeness check and defined opinion timelines apply, and the existing exemption remains valid pending the Commission's final decision. (Confirm the applicable procedure against ECHA at the time of filing.)
This continuation rule is why exemption expiry dates alone do not tell the full story. The practical status of an entry depends on whether a renewal was filed and where it sits in the pipeline.
What is changing in 2025 and 2026
Regulatory attention has shifted from adding restrictions to narrowing existing lead exemptions. The current direction:
Lead exemption restructuring. Three Commission Delegated Directives of 8 September 2025, (EU) 2025/1802, (EU) 2025/2363 and (EU) 2025/2364, split the main lead exemptions for high-melting-temperature solders, glass and ceramic components, and metal alloys into narrower, dated sub-entries. Member States transposed them by 30 June 2026, and they apply from 1 July 2026. Several renewed entries now expire between December 2026 and December 2027. Certivo breaks down the split in extended, split and revoked lead exemptions.
Annex II and Annex III updates. For the broader annex-level picture, see Certivo's RoHS 2026 to 2027 update on Annex II and Annex III changes.
Further lead and cadmium revisions proposed. On 8 July 2026 the Commission published a draft Delegated Directive proposing to renew, consolidate, split or revoke more than 20 lead and cadmium exemptions across Annex III and Annex IV, spanning fluorescent lamp glass, optical filter glass, medical phototherapy equipment, laser tubes, oxygen sensors and MRI equipment. The proposal did not change concentration limits. Confirm its adoption status and transposition dates against EUR-Lex before relying on it.
No ESPR merger. The Commission's December 2023 evaluation concluded that RoHS should be improved rather than replaced, and the Directive is not being folded into the Ecodesign for Sustainable Products Regulation.
The pattern for manufacturers is consistent: exemptions are becoming narrower, more application-specific and more time-bound, which raises the cost of tracking them by hand.
Managing RoHS alongside REACH, POPs and Prop 65 across the same parts? See how a single screen handles overlapping restrictions in Certivo's view on RoHS and REACH compliance, or talk to the Certivo team.
Managing RoHS exemptions across the bill of materials
For a manufacturer with thousands of parts, the hard part is not reading the Directive. It is answering, at any moment, which parts rely on which exemption, which products containing those parts ship to the EU, and when each exemption expires or narrows.
Spreadsheets struggle here for three reasons. Exemptions are revised on their own schedules, so a tracker is accurate only until the next delegated directive. Entries are split into sub-entries with different scopes and dates, so a part that was covered may no longer be. And the placed-on-market and spare-parts history that keeps legacy equipment serviceable lives in separate systems.
This is where a compliance system of record earns its place. Certivo models RoHS exemptions, their conditions and their expiry dates against the bill of materials, so the question "which parts lose an exemption on this date" is answerable at BOM and SKU level rather than reconstructed each audit cycle. The platform covers 150+ regulations and standards, which lets RoHS, REACH, POPs and Prop 65 be screened against the same components in one place.
CORA-powered regulatory intelligence runs this as a continuous loop. Certivo's Scout capability watches regulatory change, expires the documents affected by a narrowed or lapsed exemption, and sends the affected parts back through screening, so a change in Brussels surfaces as a specific list of affected parts rather than a newsletter. Because the engine is deterministic and traceable, each exemption decision carries an evidence trail that supports the EN IEC 63000 technical file and keeps the result audit-ready across frameworks.
When evaluating any platform for this, the question worth asking is not whether it stores exemption sunset dates, since most tools do. It is whether the tool re-screens the bill of materials automatically when an exemption changes, and whether the output traces back to the specific rule and evidence rather than a summary. Certivo's approach to tracking compliance by BOM is built around that test.
Keep RoHS exemption status current across your portfolio
RoHS exemptions are narrowing, splitting and expiring on staggered schedules, and the parts that rely on them sit across a bill of materials that changes with every engineering revision. Tracking that by hand leaves gaps that surface during audits and customer requests.
Certivo gives compliance teams a system of record that maps RoHS exemptions and their expiry dates to the BOM, re-screens parts when an exemption changes, and keeps the evidence trail audit-ready. Book a compliance review to see your current RoHS exemption exposure mapped against your products and supply chain.
Kevin Quan
Kevin Quan is Chief Marketing Officer at Certivo, where he works at the intersection of customers, compliance, and AI. Kevin brings more than two decades of experience in enterprise software, helping bring CRM, unified communications, and social platforms to market in their early waves.


